Perlakuan Panas Bertingkat sebagai Upaya Meningkatkan Kekuatan Mekanik Baja Karbon Rendah

Authors

  • Muhamad Fajar Sidiq Universitas Pancasakti Tegal
  • Galuh R.W Universitas Pancasakti
  • Royan H3 Universitas Pancasakti
  • Okky Hendra H Universitas Pancasakti
  • Saufik Luthfianto Universitas Pancasakti

DOI:

https://doi.org/10.23887/jstundiksha.v11i1.35136

Keywords:

treatment bertingkat, arang, sifat fisik.

Abstract

Penggunaan suhu pemanasan yang tidak sesuai juga tidak akan meningkatkan kekerasannya secara signifikan apalagi jika menggunakan bahan baku dengan kualitas yang rendah dari faktor kekerasan yang dimilikinya. Oleh karena itu, untuk meningkatkan ketahanan logam dalam keausan dan meningkatkan kekerasannya adalah dengan proses perlakuan panas. Tujuan penelitian ini adalah untuk mengetahui pengaruh perlakuan panas bertingkat sebagai upaya meningkatkan kekuatan mekanik baja karbon rendah.  Instrumen yang digunakan dalam pengujian ini antara lain, mesin gerinda potong, tang penjepit, sarung tangan, wadah media pendingin, tungku heat treatment, torch flame hardenin. Dari hasil penelitian ini didapatkan baja karbon rendah mengalami peningkatan kekerasan dan ketahanan geseknya selama karburising dan hardening, akan tetapi mengalami penurunan dan kenaikan laju korosi meningkat setelah mengalami proses tempering.

References

Anwar, M. S., Yulianto, E. J., Chandra, S. A., Hakim, R. N., Hastuty, S., & Mabruri, E. (2019). Pengaruh Perlakuan Panas terhadap Struktur Mikro, Kekerasan dan Ketahanan Oksidasi Suhu Tinggi pada Baja Tahan Karat Martensitik 13Cr3Mo3Ni-Cor. Teknik, 40(1), 11. https://doi.org/10.14710/teknik.v40i1.2 3058.

Budianto, E., Agus Choiron, M., & B. Darmadi, D. (2016). Hardening Baja AISI 1045 Menggunakan Gel Aloe Vera Sebagai Media Pendingin. Jurnal Rekayasa Mesin, 7(2), 55–64. https://doi.org/10.21776/ub.jrm.2016.0 07.02.3.

Budiarto, B., & Turnip, K. (2018). Analisis Pengaruh Holding Time terhadap Sifat Mekanis dan Struktur Mikro pada Proses Induction Tempering Batang Piston Baja SCM 420 H. Jurnal Rekayasa Mesin, 9(3), 235–239. https://doi.org/10.21776/ub.jrm.2018.0 09.03.11.

Callister, W. D. (2007). Materials Science. John Wiley & Sons, Inc.

Hafeez, M. A., Inam, A., & Farooq, A. (2020). Mechanical and Corrosion Properties of Medium Carbon Low Alloy Steel After Cyclic Quenching and Tempering Heat- Treatments. Materials Research Express, 7(1). https://doi.org/10.1088/2053- 1591/ab6581.

Han, G., Xie, Z. J., Li, Z. Y., Lei, B., Shang, J., C., & Misra, R. D. K. (2017). Evolution of Crystal Structure of Cu Precipitates in A Low Carbon Steel. Materials and Design, 135, 92–101. https://doi.org/10.1016/j.matdes.2017.0 8.054.

Herbirowo, S., Puspasari, V., Primatama, M. I., Hendrik, H., Astawa, I. N. G. P., Adjiantoro, B., & Pramono, A. W. (2020). Pengaruh Perlakuan Panas Karburisasi Austemper pada Baja Laterit Paduan Cr-Mo terhadap Sifat Mekanik dan Struktur Mikro. Jurnal Teknologi Bahan Dan Barang Teknik, 10(1), 19. https://doi.org/10.37209/jtbbt.v10i1.165.

Huang, Y., Zhao, C., Li, N., Zhang, H., Yu, J., & Li, J. (n.d.). Microstructure Evolution of DD6 During Different Heat Treatment Conditions. Materials Research Express, 7(1). https://doi.org/10.1088/2053- 1591/ab56a1.

Kartikasari, R., Susiana, A., & Ocktavian, D. (2021). Peningkatan Kekerasan dan Ketahanan Korosi Paduan Fe-2,9Al- 0,4C dengan Proses Karburisasi Padat. Dinamika Teknik Mesin, 11(1), 1–9. https://doi.org/10.29303/ dtm.v11i1.352.

Kumar, V., Joshi, P., Dhakad, S., Shekhar, H., Singh, S., & Kumar, S. (2015). Analysis of the Effect of Sensitization on Austenitic Stainless Steel 304L Welded by GTAW Process. Journal of Technology Innovations and Research (IJTIR), 14, 1 – 121.

Le, H., Nguyen, C.-S., & Bui1, A.-H. (2018). Experimental Processing of Ultra-Low Carbon Steel Using Vacuum Treatment. Acta Metallurgica Slovaca, 24(1), 4–12. https://doi.org/10.12776/ams.v24i1.107 0.

Lebudi, C. L., Phiri, R. R., Leso, T., & Oladijo, O. P. (2020). Effect of Heat Treatment Hardening on the Dry Sliding Wear Behaviour of Mild Steel. MRS Advances, 5(23–24), 1195–1202. https://doi.org/10.1557/adv.2020.72.

Luthfianto, S., Suprayogi, Z. A., & Samyono, D. (2017). Pengaruh Variasi Media Quenching terhadap Sifat Mekanis Rantai Elevator Fruit Kelapa Sawit. JST: Jurnal Sains Dan Teknologi, 6(1), 1–9. https://doi.org/10.23887/jst- undiksha.v6i1.9396.

Mirzaei, S., Saghafian, H., Beitollahi, A., Swierczek, J., & Tiberto, P. (2019). Effect of Heat Treatment on the Microstructure and Soft Magnetic Proper- ties of the Amorphous Fe-B-P- Cu Alloy. Iranian Journal of Materials Science and Engineering, 16(2), 1–9. https://doi.org/10.22068/ijmse.16.2.1.

Motagi, B. S., & Bhosle, R. . (2012). Effect of Heat Treatment on Microstructure and Mechanical Properties of Medium Carbon Steel. International Journal of Engineering Research and Development, 2(1), 7–13.

Paristiawan, P. A., Ridlo, F. M., Prasetyo, M. A., & Chandra, S. A. (2021). Pengaruh Variasi Media Pendingin dan Variasi Holding Time pada Proses Perlakuan Panas terhadap Sifat Mekanik dan Struktur Mikro pada Baja Mangan Fe-10.5Mn-1.3Mo-2.5Ni. Jurnal Rekayasa Mesin, 12(3), 573 – 580. https://doi.org/10.21776/ub.jrm.2021.012.03.7.

Perdana, D. (2017). Pengaruh Variasi Temperatur pada Proses Perlakuan Panas Baja Aisi 304 terhadap Laju Korosi. Teknika : Engineering and Sains Journal, 1(1), 67–72. https://doi.org/10.51804/tesj.v1i1.70.67-72.

Permana, T. S. G., & Rumendi, U. (2014). Analisa Uji Keausan Material St 37 Hasil Carburizing dan Hardening dengan Menggunakan Mesin Uji Keausan Horizontal. STEMAN, 1–5.

Priambodo, T. A., & Widyanto, B. (2015). Perubahan Struktur Mikro dan Sifat Mekanik Akibat Pemanasan di atas Temperatur Kerja pada Material Sudu Turbin Nickel Based Superalloys Srr 99. Jurnal Teknologi Bahan Dan Barang Teknik, 5(1), 39. https://doi.org/10.37209/jtbbt.v5i1.57.

Priyotomo, G., A, I. N. G. P., Stawa, & Rokhmanto, F. (2021). Efek Perlakuan Panas terhadap Sifat Mekanik Logam Stainless Steel Seri J4. TEKNIK, 42(2), 117–122. https://doi.org/10.14710/teknik.v42i2.36461.

Rahmadianto, F., Purnowidodo, A., & Soenoko, R. (2014). Upaya Peningkatan Sifat Mekanik Baja Mild Steel Melalui Perbaikan Kualitas dengan Heat Treatment Annealing dan Holding Time pada Heat Treatment dengan Taguchi Method. Jurnal Rekayasa Mesin, 5(1), 9–16.

Rahman, S. M. M., Karim, K. E., & Simanto, H. S. (2016). Effect of Heat Treatment on Low Carbon Steel : An Experimental Investigation. Applied Mechanics and Materials, 860, 7–12. https://doi.org/10.4028/www.scientific.n et/AMM.860.7.

Rile, G. (2019). Advanced Heat Treatment Equipment Technology and Product Development of Metal Materials. Journal of Physics: Conference Series, 1213(5). https://doi.org/10.1088/1742- 6596/1213/5/052117.

Saefuloh, I., Haryadi, Zahrawani, A., & Adjiantoro, B. (2018). Pengaruh Proses Quenching dan Tempering terhadap Sifat Mekanik dan Struktur Mikro Baja Karbon Rendah dengan Paduan Laterit. Flywheel: Jurnal Teknik Mesin Untirta, 4(1), 56–64. Retrieved from http://jurnal.untirta.ac.id/index.php/jwl.

Sahnesarayi, M. K., Sarpoolaky, H., & Rastegari, S. (2019). Influence of Multiple Coating and Heat Treatment Cycles on The Performance of A Nano- TiO2 Coating in The Protection of 316L Stainless Steel Against Corrosion Under UV Illumination and Dark Conditions. Iranian Journal of Materials Science and Engineering, 16(2), 33–42. https://doi.org/10.22068/ijmse.16.2.33.

Saparin. (2016). Pemanfaatan Cangkang Buah Karet Sebagai Alternatif Carburizer pada Proses Pack Carburizing Baja Karbon Rendah ST.37. Machine; Jurnal Teknik Mesin, 2(2), 17–22.

Sari, N. H. (2017). Perlakuan Panas Pada Baja Karbon: Efek Media Pendinginan terhadap Sifat Mekanik dan Struktur Mikro. Jurnal Teknik Mesian, 6(4), 263–267. https://doi.org/10.22441/jtm.v6i4.2091.

Seikh, A. H. (2013). Influence of Heat Treatment on The Corrosion of Microalloyed Steel in Sodium Chloride Solution. Journal of Chemistry. https://doi.org/10.1155/2013/587514.

Senthilkumar, T., & Ajiboye, T. K. (2018). Effect of Heat Treatment Parameters on Mechanical Properties of DSedium Carbon Steel. Mechanics and Mechanical Engineering, 22(4), 909–918. https://doi.org/10.2478/mme 2018-0071.

Shi, C., Qu, B., & Provis, J. L. (2019). Recent Progress in Low-Carbon Binders. White Rose Research, 122, 227–250. https://doi.org/10.1016/j.cemconres.2019.05.009.

Shuaib-Babata, Y., & Adewuyi, R. A. (2016). Effects of Thermal Treatment Processes (TTP) on the Tensile Properties of 0.165% Carbon Steel. FUOYE Journal of Engineering and Technology, 1(1), 15–19. https://doi.org/10.46792/fuoyejet.v1i1.1 0.

ESidiq, M. F., Willis, G. R., & Shidik, M. A. (2020). The Effect of Coffee Powder as A Carburizing Agent and Preventing Corrosion The Effect of Coffee Powder as A Carburizing Agent and Preventing Corrosion. Annual Conference on Computer Science and Engineering Technology (AC2SET), 1–8. https://doi.org/10.1088/1757- 899X/1088/1/012084.

Trihutomo, P. (2015). Analisa Kekerasan pada Pisau Berbahan Baja Karbon Menengah Hasil Proses Hardening dengan Media Pendingin yang Berbeda. Jurnal Teknik Mesian, 23(1), 29–34. Retrieved from http://journal.um.ac.id/index.php/teknik-mesin/article/view/5358/2053.

Downloads

Published

2022-02-27

Issue

Vol. 11 No. 1 (2022)

Section

Articles

License

Copyright (c) 2022 JST (Jurnal Sains dan Teknologi)

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Authors who publish with the Jurnal Sains dan Teknologi (JST)   agree to the following terms:

  1. Authors retain copyright and grant the journal the right of first publication with the work simultaneously licensed under a Creative Commons Attribution License (CC BY-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal. 
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work. (See The Effect of Open Access)